Media Releases

02/28/2019

New HP Coupling from Voith allows realistic tests in all speed ranges

  • Voith’s new HP Coupling protects the test rig against damaging torsional vibrations and natural frequencies
  • The further enhanced Voith Hydrodamp vibration damper secures the driveline even at high speeds and temperatures
  • Voith offers an individualized fine adjustment for the spring assemblies and adapts them to customer connections
The HP Coupling from Voith protects the test rig against damaging torsional vibrations and natural frequencies.
ESSEN, Germany. The new HP Coupling from Voith was designed for testing internal combustion engines on test rigs under realistic conditions. Its Voith Hydrodamp Technology, which has undergone further development, protects the driveline even at high speeds and temperatures.

In the automotive industry, the new, highly flexible HP Coupling protects the driveline of test rigs against critical torsional vibrations. Such vibrations are unavoidable when testing internal combustion engines and put stress on the connected components. In addition, the HP Coupling shifts critical resonant frequencies of the system below the operating speed range and dampens undesired alternating torques. This increases the service life of all drive components of the test rig.

In past years, the standards for these routine tests have undergone considerable change. For the test engineers to get results that largely corresponded to everyday conditions, they rely on bell-house mounted arrangements instead of drive shaft arrangements. In this process, a realistic dummy transmission is flange-mounted to the internal combustion engine, thus simulating the drive train in a vehicle to a very great degree. With reinforced spring assemblies, an enhanced coupling seal and a damping grease optimized for temperature, the new HP Coupling from Voith provides maximum protection for the test rig even with this new test procedure.

The HP Coupling contains another innovation; the springs operate reliably over a wide speed range allowing test runs of up to 8500 rpm. Even the damping grease is designed for high speeds and the associated temperatures, ensuring reliable operation of the coupling up to a temperature of 150 degrees Celsius. The optimized lubricant also provides better damping that reduces alternating torques in the drive train to a minimum. This increases the service life of all components connected in the test rig. Voith offers up to 16 different spring hardness values. This makes it possible to finely adjust the coupling with precision to the requirements of the customer.

The additional visco-hydraulic damping of the HP Coupling increases the damping effect in proportion to the coupling’s angle of twist. This is the decisive benefit over arc spring couplings used in bell-house mounted test rig arrangements today. Severe torsional vibrations, such as those occurring in typical test scenarios, also lead to high damping in this case. This gives the coupling optimal damping behavior across the entire nominal speed range.

When sealing the coupling, Voith has further enhanced the proven Voith Hydrodamp Technology with an additional sealing sheet including the seal. This prevents grease from escaping due to the centrifugal forces that occur at high speeds. A special PEEK material increases the spring assemblies’ resistance to wear and strength at high speed, substantially improving the service life of the HP Coupling.

Thanks to this enhanced Voith Hydrodamp Technology, the new HP Coupling from Voith permits realistic tests over all speed ranges. As the coupling also protects the test rig against critical torsional vibrations and natural frequencies, downtimes are decreased, thereby reducing costs and increasing the general cost-effectiveness of the test rig.

In initial prototype tests at a well-known vehicle manufacturer, the HP Coupling satisfied all the requirements for temperature stability and speed. Voith will debut the new HP Coupling at the Automotive Testing Expo 2019 in Stuttgart at fair booth 1374.

About the company
The Voith Group is a global technology company. With its broad portfolio of systems, products, services and digital applications, Voith sets standards in the markets of energy, oil & gas, paper, raw materials and transport & automotive. Founded in 1867, the company today has more than 19,000 employees, sales of € 4.2 billion and locations in over 60 countries worldwide and is thus one of the large family-owned companies in Europe.

The Group Division Voith Turbo is part of the Voith Group and a specialist for intelligent drive solutions, systems as well as comprehensive services. Customers from highly diverse industries such as oil and gas, energy, rail and commercial vehicles, ship technology, mining and mechanical engineering rely on the advanced technologies and solutions-driven expertise of Voith.

Contact

Robin Wankerl

Global Market Communication Manager

 

t +49-7321-37-8303